Temperature regulator, controller for boiler with piston feeder TANGO - hot water version
- Watch the product:
- Add feedback:
- Code: 5076
- Manufacturer: FOSTER
- Manufacturer's code: 2001230050764
- Weight: 3 kg
- Availability: None
-
- Net Price: €90.24 €111.00
- szt.
-
Payment in cash, Payment via bank transfer, Online Payments Payment Cards, ApplePay, Google Pay - P24, PayPro SA, Osobista płatność przy odbiorze, Płatność odroczona (tylko dla zweryfikowanych Klientów), eService (card or bank transfer), Zapłacę przy odbiorze listonoszowi, Payment by bank transfer - wait for the proforma invoice to be sent
-
Fast Blik payments.
The product is shipped within 24 hours.
We complete the order within 24 hours.
You can return the product within 14 days.
The microprocessor temperature controller for the TANGO boiler is a device used to control the operation of a boiler with a fuel feeder. It allows for the regulation of water temperature in the installation by controlling the boiler's actuators, i.e., the fuel feeder, blower, and circulation pump.
In the TANGO - PISTON controller version, a special algorithm for reversing the feeder motor in case of jamming has been applied.
CONTROLLER EQUIPMENT
1. Water temperature sensor in the boiler.
2. Input for connecting the feeder position sensor. The sensor contact should be closed when the feeder is in the output position.
3. Input for connecting the basket thermostat. During operation, this input should be closed; upon exceeding the allowable basket temperature, it should open.
4. Input for connecting the room thermostat. Below the set room temperature, it should be closed, and upon reaching the temperature - open. If no room thermostat is used, the input must be permanently closed.
5. Signal input for additional equipment failure. Raising the voltage to 230 V AC triggers the controller's "failure" state. It can be used, for example, to stop the controller after feeder motor overload (after using an additional overload switch).
6. Data transmission connector to other microprocessor devices. It can be used to connect additional devices, e.g., weather controller, remote control panel, etc.
7. Feeder motor output - allows connection of a single-phase 230 V AC motor with a rated current up to 4A in a four-wire connection for changing rotation direction - terminals: C-L-L-LR, or two-wire without the possibility of changing rotation direction - terminals: L-L.
8. Circulation pump output - for connecting a single-phase 230 V AC pump with a rated current up to 1 A.
9. Domestic hot water pump output.
10. Blower output - for connecting a single-phase 230 V AC blower with a rated current up to 1 A.
11. Chimney exhaust output (optional) - for connecting a single-phase 230 V AC fan with a rated current up to 1 A.
12. Failure signal output - normally open contact, 230 V AC, load capacity up to 1 A - for connecting an additional controller failure indicator.
13. Two-part connectors for connecting external devices, preventing the interchange of connectors with wiring. This allows disconnecting the controller from the boiler equipment during service without the need to unscrew wires.
TECHNICAL PARAMETERS
- Number of operating modes: 2
- Upper set temperature: 65-90 °C
- Lower set temperature: 20-60 °C
- Circulation pump activation temperature: 20-60 °C
- Hysteresis: 0.5-5.0 °C
- Emergency hardware thermostat activation temperature: 94 °C
- Feeder operation time:
- version with piston feeder: 1 cycle
- version with screw feeder: 1-255 s - Feeder pause time: 30-999 s
- Standby waiting time: 1-250 min
- Controller shutdown temperature: 20-45 °C
- Controller weight: 2.3 kg
OPERATING CONDITIONS
- Ambient temperature: 5-40 °C
- Supply voltage: 230 V AC 50 Hz
- Output load capacity:
- pump: 230 V, 1(1) A
- blower: 230 V, 1(1) A
- exhaust (optional): 230 V, 1(1) A
- feeder: 230 V, 4(4) A - Maximum sensor operating temperature: 100 °C
Polish
Czech
German
Slovak
Ukrainian