Controller for DS-100 pump and IBO 25-40 central heating pump set for a loading boiler furnace

Produkty > Sterowniki i regulatory > zestawy do kotłów - sterowanie

Code: 13067
Producer: DOMER
Producer code: 2001230130671

Weight: 3kg
Price gros: €46.07
Price net: €37.46

Set for stove controller of C.O. pump and pump

DS-100 controller and IBO 25/40/180 pump

Special features:

Polish product
excellent quality
directly from the manufacturer
the cheapest set on the market
easy operation

TECHNICAL DATA OF THE CONTROLLER

Temperature control range (set temperature): 20 C - 80 °C
Hysteresis: 2 °C
Power supply voltage: 230 V / 50 Hz ± 10 %
Power consumption: < 1 W
Operating temperature: 20 - 70 °C
Temperature sensor: resistive
Cross-section of connection wires: 3 x 0.75 mm2
Sensor cable length: 0.9 m
Power cord length: 1.3 m
Pump power supply cable length: 1.3 m
Pump power supply: 230 V / 50 Hz
Dimensions (width x height x length): 59 mm x 40 mm x 85 mm
Maximum output load current: 1A (relay)

TECHNICAL PARAMETERS OF THE PUMP

Weight: 2.6 kg
Connections: 1 1/2 inch
Thread connection size: 47.5 mm (measured outside the thread)
Installation length: 180 mm
Minimum liquid temperature: +2 degrees C
Maximum liquid temperature: +110 degrees C
Maximum operating pressure: 1.0 MPa
Power supply: 230/240 V - 50 Hz
Protection rating: IP44
Insulation class: I
Water column lift: 4 m
Do not install the pump with the motor facing up or down. The motor should always be placed horizontally
Do not run the pump "dry"

POWER AND CURRENT SUPPLY:

1st speed - 38 W / 0.12 A
2nd speed - 53 W / 0.16 A
3rd speed - 72 W / 0.20 A

LIFT

1st speed - 2 meters
2nd speed - 3 meters
3rd speed - 4 meters

The pump is used in central heating systems including underfloor heating, domestic hot water, and drinking water.

PRINCIPLE OF OPERATION

The DS-100 DOMER controller is designed to control the C.O. water circulation pump. The controller's task is to turn on the pump if the temperature exceeds the desired value. This prevents unnecessary pump operation, saving electrical energy (savings depending on the degree of stove use can reach up to 60%) and extends the pump's lifespan. This increases its reliability and reduces operating costs.

The pump activation temperature is adjustable with a potentiometer in the range of 20 °C to 80 °C. The pump turns off if the actual temperature drops 2 degrees Celsius below the set temperature (adjusted by the potentiometer). The S-100 controller, besides the potentiometer, has two switches. The first switch is for turning on the controller (indicated by a green LED), while the second red switch is for manual pump activation. Two additional lit LEDs indicate: yellow - operation, red - pause (standstill).

BASIC FUNCTIONS OF THE PUMP

IBO - OHI pumps are designed to force water circulation in central heating and domestic hot water installations. They can also be used in solar heating systems, air conditioning, and cooling circulation systems.

With the pump, the customer receives gaskets for unions (2 pieces), a Polish user and installation manual, and a warranty card.

The pump installation should be done on a straight pipe section between two shut-off valves, in a place accessible for venting, inspection, or service. The pump should be installed so that the pump axis is positioned horizontally. Before starting the pump installation, be sure to read the user manual.

MAIN AREAS OF APPLICATION

Circulation pumps are used in installations with constant or slightly variable flow, such as:

heating installations
heating systems

CONSTRUCTION - HYDRAULIC PART

sealless centrifugal pump
threaded cast iron housing
pump impeller made of composite material

CONSTRUCTION - MOTOR

asynchronous 2-pole
ceramic shaft and radial bearings
carbon thrust bearing
insulation class I
voltage: 1~230/240 V
three-speed speed control
protection rating IP 44

ADVANTAGES

energy efficiency
reliability and dependability
ease of installation
quiet operation up to 38 dB(A)
high quality workmanship
no maintenance required
built-in short-circuit protection

THE PUMP IS NOT EQUIPPED WITH UNIONS, GASKETS, OR CABLE.

Set for furnace controller of C.O. pump and pump

Controller DS-100 and pump IBO 25/40/180

Special features:

Polish product
excellent quality
directly from the manufacturer
the cheapest set on the market
easy operation

CONTROLLER TECHNICAL DATA

Temperature regulation range (set temperature): 20 C - 80 °C
Hysteresis: 2 °C
Power supply voltage: 230 V / 50 Hz ± 10 %
Power consumption: < 1 W
Operating temperature: 20 - 70 °C
Temperature sensor: resistive
Cross-section of connection wires: 3 x 0.75 mm2
Sensor cable length: 0.9 m
Power cable length: 1.3 m
Pump power cable length: 1.3 m
Pump power supply: 230 V / 50 Hz
Dimensions (width x height x length): 59 mm x 40 mm x 85 mm
Maximum output load current: 1A (relay)

PUMP TECHNICAL PARAMETERS

Weight: 2.6 kg
Connections: 1 1/2 inch
Thread connection size: 47.5 mm (measured outside the thread)
Installation length: 180 mm
Minimum liquid temperature: +2 degrees C
Maximum liquid temperature: +110 degrees C
Maximum operating pressure: 1.0 MPa
Power supply: 230/240 V - 50 Hz
Protection rating: IP44
Insulation class: I
Water column lift: 4 m
Do not install the pump with the motor facing up or down. The motor should always be placed horizontally
Do not run the pump "dry"

POWER AND SUPPLY CURRENT:

1st speed - 38 W / 0.12 A
2nd speed - 53 W / 0.16 A
3rd speed - 72 W / 0.20 A

LIFT

1st speed - 2 meters
2nd speed - 3 meters
3rd speed - 4 meters

The pump is used in central heating systems including underfloor heating, domestic hot water, and drinking water.

PRINCIPLE OF OPERATION

The DS-100 DOMER controller is designed to control the C.O. water circulation pump. The controller's task is to turn on the pump if the temperature exceeds the desired value. This prevents unnecessary pump operation, saving electrical energy (savings depending on the furnace usage can reach up to 60%) and extends the pump's lifespan. This increases its reliability and reduces operating costs.

The pump activation temperature is adjustable with a potentiometer in the range of 20 °C to 80 °C. The pump turns off if the actual temperature drops 2 degrees Celsius below the set temperature (adjusted by the potentiometer). The S-100 controller, besides the potentiometer, has two switches. The first switch is for turning on the controller (indicated by a green LED), while the second red switch is for manual pump activation. Two additional LEDs indicate: yellow - operation, red - pause (standby).